Nice list Rick! I like the idea of the 88. We can do all the work on that. I would consider myself and expert on a fox. I have A\C equipment so that not a problem. This sounds like it gonna be a good time
| Mustang Club of Maryland http://mustangclubofmd.com/phpbb/ |
|
| Tech Day? http://mustangclubofmd.com/phpbb/viewtopic.php?f=14&t=2160 |
Page 1 of 1 |
| Author: | Bobt [ Tue Jul 22, 2008 7:40 am ] |
| Post subject: | Tech Day? |
| Author: | Big Blue [ Tue Jul 22, 2008 2:50 pm ] |
| Post subject: | |
| Author: | 5.7Lmustang [ Tue Jul 22, 2008 4:26 pm ] |
| Post subject: | |
| Author: | prodrifterx [ Tue Jul 22, 2008 5:22 pm ] |
| Post subject: | |
| Author: | Bobt [ Tue Jul 22, 2008 6:43 pm ] |
| Post subject: | |
| Author: | Rapture [ Tue Jul 22, 2008 7:55 pm ] |
| Post subject: | |
| Author: | prodrifterx [ Wed Jul 23, 2008 6:24 am ] |
| Post subject: | |
| Author: | mustang0818 [ Wed Jul 23, 2008 4:58 pm ] |
| Post subject: | |
| Author: | Rick Hinkle [ Fri Jul 25, 2008 10:36 am ] |
| Post subject: | |
MCOM needs more tech days! We all joined for the cars, so I really like the tech day concept... (of course we have a lot of fun with the social aspects, too) I have a bit too many projects that could be used for tech days - and not enough time. I will offer the cars out for the demand of club learning, but otherwise, I will also have some tech days at my house, too as time permits. Projects pending for tech days: 1965 convertible - swap 4-speed tranny to automatic C4 - rebuild rear - rebuild entire front-end - replace all brake lines and cylinders - remove and replace both rear quarter panels (& doors) 1967 fastback - replace all brake lines - rebuild front end - replace fuel lines, install elec fuel pump - replace front and rear electrical harnesses (sub-sections) - replace door glass and all mechanicals to new shells - replace door skin(s) or sub-sections 1988 Mustang GT convertible - replace front brake rotors, bearings - convert A/C from R-12 to R-134 - diagnose electrical failure of horn & lighter circuit. |
|
| Author: | Bobt [ Fri Jul 25, 2008 11:58 am ] |
| Post subject: | |
Nice list Rick! I like the idea of the 88. We can do all the work on that. I would consider myself and expert on a fox. I have A\C equipment so that not a problem. This sounds like it gonna be a good time
|
|
| Author: | Bobt [ Sun Aug 03, 2008 8:50 pm ] |
| Post subject: | |
Heres the model A that need to have a 3.73 ring and pinion and a 3500rpm stall torque convertor installed. I think im going to be doing them sooner than I had planned. Once I get the parts in anyone who would like to come up and learn something/hang out or help out is welcome to do so. It could be this saturday or next. Ill post when im sure. But check out this burn out I did. http://www.youtube.com/watch?v=684ycbDISZ8 |
|
| Author: | Bobt [ Tue Aug 05, 2008 10:52 am ] |
| Post subject: | |
| Author: | jackhardy [ Tue Aug 05, 2008 5:59 pm ] |
| Post subject: | |
| Author: | Bobt [ Fri Aug 08, 2008 11:10 am ] |
| Post subject: | |
| Author: | atlantic image [ Fri Aug 08, 2008 9:26 pm ] |
| Post subject: | im up for that |
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|